Mikuni BDS Carburetor Parts and Service Kits
Mikuni BDS Carburetor Parts and Service Kits

Mikuni BDS Parts

Mikuni BDS carburetor parts and rebuild kits.

On this page you will find all currently available parts for the Mikuni BDS range carburetors.

We are still very much expanding our parts offerings for these carburettors so please contact us by email if the part that you are looking for is not yet listed.

Our Contact Page can be found HERE.

Mikuni BDS Carburetor Parts and Service Kits

!
Mikuni BDS Jets

Mikuni BDS Jets

Mikuni BDS Jets.

The variety of Mikuni jets is really overwhelming and as the icing on the cake, there's no telling which yet was used on which motorcycle and when...

For this reason, we have decided to create one single page with all the Mikuni motorcycle jets that we can supply.

On that page you will find the exact dimensions of those jets so that you can easily compare them to the one(s) that you found in your carburetor.

The Mikuni Motorcycle Jets page can be found HERE.

Mikuni BDS Jets

KSK941YK
Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1200 Venture

Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1200 Venture

Rebuild kit for the Mikuni BDS carburetors as used on the Yamaha XVZ1200 Venture motorcycles.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Various Viton (rubber) o-rings as depicted in the photograph
  • Various screws as depicted in the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha XVZ 1200, they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture.

Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1200 Venture

KSK941YK
Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1300 Venture

Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1300 Venture

Rebuild kit for the Mikuni BDS carburetors as used on the Yamaha XVZ1300 motorcycles.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Various Viton (rubber) o-rings as depicted in the photograph
  • Various screws as depicted in the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha XVZ 1300, they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture.

Service Kit for Mikuni BDS Carburetors on Yamaha XVZ 1300 Venture

KSK941YK
Service Kit for Mikuni BDS Carburetors on Yamaha VMX 1200 V-Max

Service Kit for Mikuni BDS Carburetors on Yamaha VMX 1200 V-Max

Rebuild kit for the Mikuni BDS carburetors as used on the Yamaha VMX1200 V-Max motorcycles.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Various Viton (rubber) o-rings as depicted in the photograph
  • Various screws as depicted in the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha VMX 1200 , they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture..

Service Kit for Mikuni BDS Carburetors on Yamaha VMX 1200 V-Max

KSKY0542F
Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - FRONT

Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - FRONT

This is our comprehensive rebuild kit for the Mikuni BDS carburetors as used on the Yamaha XV535 Virago motorcycles.

These sets include the jets as since the jet sizing is different for Front and Rear carb on the 535, there are two different sets.

This particular set is for the FRONT carburetor.

The set for the rear carburetor can be found HERE.

Alternatively, there is also a less elaborate service kit available which can be found HERE.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Jet needle 5DZ10 - Replaces Mikuni numbers 2GV-1490J-00 and 3BM-1490J-00
  • Needle jet - Replaces Mikuni number 2JU-14141-08
  • Jet size 170 - replaces Mikuni number 3G2-14231-34
  • Jet size 135 - replaces Mikuni number 3G2-14231-27
  • Jet size 70 - replaces Mikuni number 3G2-14231-14
  • Idle jet size 35 - replaces Mikuni number 4G0-14142-35-A0
  • Pipe - replaces Mikuni number 2JU-1414G-00
  • Various Viton (rubber) o-rings as per the photograph
  • Various screws as per the photograph
  • Various springs and small material as per the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha XV 535 , they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture.

Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - FRONT

KSKY0542R
Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - REAR

Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - REAR

This is our comprehensive rebuild kit for the Mikuni BDS carburetors as used on the Yamaha XV535 Virago motorcycles.

These sets include the jets as since the jet sizing is different for Front and Rear carb on the 535, there are two different sets.

This particular set is for the REAR carburetor.

The set for the front carburetor can be found HERE.

Alternatively, there is also a less elaborate service kit available which can be found HERE.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Jet needle 5DZ9 - Replaces Mikuni numbers 2GV-1490J-10 and 3BM-1490J-10
  • Needle jet - Replaces Mikuni number 2JU-14141-08
  • Jet size 170 - replaces Mikuni number 3G2-14231-34
  • Jet size 137.5 - replaces Mikuni number 3G2-1423A-78
  • Jet size 70 - replaces Mikuni number 3G2-14231-14
  • Idle jet size 35 - replaces Mikuni number 4G0-14142-35-A0
  • Pipe - replaces Mikuni number 2JU-1414G-00
  • Various Viton (rubber) o-rings as per the photograph
  • Various screws as per the photograph
  • Various springs and small material as per the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha XV 535 , they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture.

Comprehensive Service Kit for Mikuni BDS Carburetor on Yamaha XV 535 Virago - REAR

KSK941YK
Service Kit for Mikuni BDS Carburetors on Yamaha XV 535 Virago

Service Kit for Mikuni BDS Carburetors on Yamaha XV 535 Virago

This is our standard rebuild kit for the Mikuni BDS carburetors as used on the Yamaha XV535 Virago motorcycles.

If you desire a more elaborate kit, you can find the comprehensive kit for the FRONT carburetor HERE and the one for the REAR carburetor HERE.

This service kit contains the following parts to service 1 carburettor:

  • Float Bowl Gasket
  • Top Cover Gasket
  • Jet Block Gasket
  • Needle Valve Set
  • Mixture Screw Set
  • Various Viton (rubber) o-rings as depicted in the photograph
  • Various screws as depicted in the photograph

Although these carburetors were originally delivered on the above mentioned Yamaha XV 535 , they are often transplanted onto other bikes and engines so the range that these service kits might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the parts shown will fit your bike.

This is a Carburetor City rebuild kit of superb Japanese manufacture.

Service Kit for Mikuni BDS Carburetors on Yamaha XV 535 Virago

KSSD109
(7) Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV535 Virago

(7) Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV535 Virago

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors as used on, amongst others, the Yamaha XV535 Virago.

Normally this diaphragm is not available as a separate spare part but as the existing stocks of complete throttle slides are getting depleted, this is an excellent alternative to such a complete slide.

Please note that replacing this diaphragm does require a certain degree of handicraft.
Please read the instructions carefully before making your purchase.
The instructions can be found HERE.

This diaphragm is supplied complete with the glue and tie-strap that are required for the assembly.

This is item number 7 in the drawing.

This is a Carburetor City replacement diaphragm of excellent German manufacture.

(7) Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV535 Virago

KSM106A
(18) Jet Block Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

(18) Jet Block Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

Replacement gasket for the jet block on the Mikuni BDS carburetors as used on, amongst others, the Yamaha XV535 Virago.

This is our part number KSM106A which replaces the following Mikuni / Yamaha numbers:

  • 22U-14199-00-00 
  • 3JB-14199-00-00

Required quantity per carburetor: 1

This is item number 18 in the drawing.

 

(18) Jet Block Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

KSYT24A
(44 + 45) Drain Plug for Mikuni BDS carburetors for Yamaha XV535 Virago

(44 + 45) Drain Plug for Mikuni BDS carburetors for Yamaha XV535 Virago

Float Bowl Drain Plug for the Mikuni BDS carburetor on the Yamaha XV 535 Virago.

Replaces Mikuni part numbers: 12R-14191-00 (old) and 2L1-14191-00 (new)

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

This is numbers 44 + 45 in the drawing.

(44 + 45) Drain Plug for Mikuni BDS carburetors for Yamaha XV535 Virago

KSK17B
Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300 Venture

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300 Venture

Rubber (Viton) gasket to seal the float bowl on the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XVZ 1300 Venture.

This seal fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Replaces Mikuni part number: 22V-14147-00

 

 

 

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300 Venture

KSK17B
(31) Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

(31) Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

Rubber (Viton) gasket to seal the float bowl on the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XV 535 Virago.

This seal fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Replaces Yamaha part number: 22V-14147-00

Required quantity per carburetor: 1

This is item number 31 in the drawing.

(31) Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XV535 Virago

KSK17B
Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha V-Max VMX1200

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha V-Max VMX1200

Rubber (Viton) gasket to seal the float bowl on the Mikuni BDS series carburetors as used on, amongst others, the Yamaha V-Max VMX 1200.

This seal fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Replaces Mikuni part number: 22V-14147-00

 

 

 

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha V-Max VMX1200

KSK17B
Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1200 Venture

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1200 Venture

Rubber (Viton) gasket to seal the float bowl on the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XVZ 1200 Venture.

This seal fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Replaces Mikuni part number: 22V-14147-00

 

 

 

Rubber Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1200 Venture

KSN167031A
(24) Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

(24) Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

Original Mikuni rubber cap to seal the main jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XV 535 Virago.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167031a
Yamaha part number: 22U-14968-00-00

This is item number 24 in the drawing.

(24) Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

KSN167032
(25) Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

(25) Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

Original Mikuni rubber cap to seal the idle (or slow running) jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XV535 Virago.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167032
Yamaha part number: 22V-14968-00-00

This is item number 25 in the drawing.

(25) Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV535 Virago

KSN167031A
Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

Original Mikuni rubber cap to seal the main jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XVZ 1200 Venture.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167031a

 

 

 

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

KSN167032
Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

Original Mikuni rubber cap to seal the idle (or slow running) jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XVZ 1200 Venture.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167032

 

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XVZ1200 Venture

KSN167031A
Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

Original Mikuni rubber cap to seal the main jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha V-Max VMX 1200.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167031a

 

 

 

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

KSN167032
Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

Original Mikuni rubber cap to seal the idle (or slow running) jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha V-Max VMX 1200.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167032

 

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha V-Max VMX1200

KSN167031A
Rubber Plug for the Main Jets on the Mikuni BDS carburetors for Yamaha XV500

Rubber Plug for the Main Jets on the Mikuni BDS carburetors for Yamaha XV500

Original Mikuni rubber cap to seal the main jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamah XV 500.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167031a

 

 

 

Rubber Plug for the Main Jets on the Mikuni BDS carburetors for Yamaha XV500

KSN167032
Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV500

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV500

Original Mikuni rubber cap to seal the idle (or slow running) jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XV 500.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167032

 

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV500

KSN167031A
Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1300 Venture

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1300 Venture

Original Mikuni rubber cap to seal the main jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XVZ 1300 Venture.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167031a

 

 

 

Rubber Plug for the Main Jets on the Mikuni BDS carburetors of the Yamaha XVZ1300 Venture

KSN167032
Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV1300 Venture

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV1300 Venture

Original Mikuni rubber cap to seal the idle (or slow running) jets on the Mikuni BDS series carburetors as used on, amongst other, the Yamaha XVZ1300 Venture.

This plug fits both the Mikuni BDS34 as well as the Mikuni BDS35.

Mikuni part number: N167032

 

Rubber Plug for the Idle Jets on the Mikuni BDS carburetors of the Yamaha XV1300 Venture

KSSD107
Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV1300

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV1300

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors as used on, amongst others, the Yamaha XV1300.

Normally this diaphragm is not available as a separate spare part but as the existing stocks of complete throttle slides are getting depleted, this is an excellent alternative to such a complete slide.

Please note that replacing this diaphragm does require a certain degree of handicraft.
Please read the instructions carefully before making your purchase.
The instructions can be found HERE.

This diaphragm is supplied complete with the glue and tie-strap that are required for the assembly.

This is a Carburetor City replacement diaphragm of excellent German manufacture.

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha XV1300

KSKYSS045
(40) Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV535 Virago

(40) Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV535 Virago

Pilot Screw Set for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XV 535 Virago.

Fits a multitude of Mikuni BDS and BDST carburetors.

This set consists of the following parts:

  • Pilot Screw
  • Pilot Screw Spring
  • Aluminum Washer
  • Viton O-Ring

Replaces Yamaha part number: 12R-14105-00

Required quantity per carburetor: 1

This is item number 40 in the drawing.

(40) Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV535 Virago

KSKVN16Q2T
(19) Needle Valve for Mikuni BDS carburetors for Yamaha XV535 Virago

(19) Needle Valve for Mikuni BDS carburetors for Yamaha XV535 Virago

Needle valve for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XV 535 Virago.

Viton-tipped for superior sealing qualities.

Replaces Mikuni part number: 3GM-14107-17-00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these diaphragms might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the needle shown will fit your bike.

This is a Carburetor City Needle Valve, Made in Japan to extremely exacting Standards.

(19) Needle Valve for Mikuni BDS carburetors for Yamaha XV535 Virago

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki GV1200 Madura - Complete

Throttle Slide for Mikuni carburetors for Suzuki GV1200 Madura - Complete

Mikuni factory original, complete, throttle slide for the Mikuni BDS carburettor of the Suzuki GV1200 Madura.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki GV1200 Madura - Complete

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Front

Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT Mikuni BDS36 carburettor of the Suzuki VS1400 Intruder.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Front

KSN192009
Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Rear

Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR Mikuni BDS36 carburettor of the Suzuki VS1400 Intruder.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS1400 Intruder - Complete - Rear

KSNTMOR013G
Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - FRONT

Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetors of the Suzuki VS1400 Intruder.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - FRONT

KSYFCG87A
Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - Rear

Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - Rear

Gasket for the float bowl of the REAR Mikuni carburetors of the Suzuki VS1400 Intruder.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS1400 Intruder - Rear

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Front

Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT Mikuni BDS36 carburettor of the Suzuki VS700 Intruder.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Front

KSN192009
Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Rear

Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR Mikuni BDS36 carburettor of the Suzuki VS700 Intruder.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS700 Intruder - Complete - Rear

KSNTMOR013G
Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Front

Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetors of the Suzuki VS700 Intruder.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Front

KSYFCG87A
Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Rear

Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Rear

Gasket for the float bowl of the REAR Mikuni carburetors of the Suzuki VS700 Intruder.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS700 Intruder - Rear

KSN178075
(F27) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Front

(F27) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT carburettor of the Suzuki VS750 Intruder.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

This is number F27 in the drawing.

(F27) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Front

KSNTMOR013G
(F33) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Front

(F33) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetor of the Suzuki VS750 Intruder.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

This is number F33 in the drawing.

(F33) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Front

KSYT24A
(F39) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Front

(F39) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Front

Float Bowl Drain Plug for the FRONT Mikuni carburetor of the Suzuki VS750 Intruder.

Comes complete with new o-ring.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

This is number F39 in the drawing.

(F39) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Front

KS88S002
(F41 + F42) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Front

(F41 + F42) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Front

Air cut-off valve for the FRONT Mikuni carburetor of the Suzuki VS750 Intruder.

Comes complete with new spring and o-ring.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

This is number F41 + F42 in the drawing.

(F41 + F42) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Front

KSN192009
(R3) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Rear

(R3) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR carburettor of the Suzuki VS750 Intruder.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

This is number R3 in the drawing.

(R3) Throttle Slide for Mikuni carburetors for Suzuki VS750 Intruder - Complete - Rear

KSYFCG87A
(R12) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Rear

(R12) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Rear

Gasket for the float bowl of the REAR Mikuni carburetor on the Suzuki VS750 Intruder.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

This is number R12 in the drawing.

(R12) Float Bowl Gasket for Mikuni carburetors for Suzuki VS750 Intruder - Rear

KS88S002
(R36 + R37) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Rear

(R36 + R37) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Rear

Air cut-off valve for the REAR Mikuni carburetor on the Suzuki VS750 Intruder.

Comes complete with new spring and o-ring.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

This is number R36 + R37 in the drawing.

(R36 + R37) Air Cut-Off Valve for Mikuni carburetors for Suzuki VS750 Intruder - Rear

KSYT24A
(R51) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Rear

(R51) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Rear

Float Bowl Drain Plug for the REAR Mikuni carburetor on the Suzuki VS750 Intruder.

Comes complete with new o-ring.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

This is number R51 in the drawing.

(R51) Drain Plug for Mikuni carburetors for Suzuki VS750 Intruder - Rear

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Front

Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT Mikuni BDS36 carburettor of the Suzuki VS800 Intruder.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Front

KSN192009
Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Rear

Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR Mikuni BDS36 carburettor of the Suzuki VS800 Intruder.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VS800 Intruder - Complete - Rear

KSNTMOR013G
Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - FRONT

Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetors of the Suzuki VS800 Intruder.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - FRONT

KSYFCG87A
Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - Rear

Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - Rear

Gasket for the float bowl of the REAR Mikuni carburetors of the Suzuki VS800 Intruder.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VS800 Intruder - Rear

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Front

Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT Mikuni BDS36 carburettor of the Suzuki VX800.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Front

KSN192009
Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Rear

Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR Mikuni BDS36 carburettor of the Suzuki VX800.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VX800 - Complete - Rear

KSNTMOR013G
Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - FRONT

Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetor of the Suzuki VX800.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - FRONT

KSYFCG87A
Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - Rear

Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - Rear

Gasket for the float bowl of the REAR Mikuni carburetors of the Suzuki VX800.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VX800 - Rear

KSN178075
Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Front

Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Front

Mikuni factory original, complete, throttle slide for the FRONT Mikuni BDS36 carburettor of the Suzuki VZ800 Marauder.

Mikuni part number: 13500-05A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.75 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Front

KSN192009
Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Rear

Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Rear

Mikuni factory original, complete, throttle slide for the REAR Mikuni BDS36 carburettor of the Suzuki VZ800 Marauder.

Mikuni part number: 13500-38A10

Please note that this slide has a balance hole with 2.4 mm diameter.
The version with a balance hole of 1.5 mm is also available on request.

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this slide will fit your bike.

Throttle Slide for Mikuni carburetors for Suzuki VZ800 Marauder - Complete - Rear

KSNTMOR013G
Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - FRONT

Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - Front

Rubber (Viton) gasket for the float bowl of the FRONT Mikuni carburetor of the Suzuki VZ800 Marauder.

Replaces Mikuni part number: 13251-38A00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - FRONT

KSYFCG87A
Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - Rear

Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - Rear

Gasket for the float bowl of the REAR Mikuni carburetors of the Suzuki VZ800 Marauder.

Replaces Mikuni part number: 13251-38A10

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this gasket will fit your bike.

Float Bowl Gasket for Mikuni carburetors for Suzuki VZ800 Marauder - Rear

flexoid5xa4
Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material.

Almost a "First Aid Kit" for the home mechanic!

This set of first quality gasket paper contains 5 sheets in DIN A4 size (300 x 210 mm or roughly 11.8 x 8.3 inches) in 5 different thicknesses.

You can cut these sheets to almost any desirable size and shape to help you out when the required gasket is not at hand.

The sheets are made of cellulose based, plasticised gelatin-impregnated material.

The sheets are of the following thickness:

  • 0.15 MM
  • 0.25 MM
  • 0.4 MM
  • 0.8 MM
  • 1.6 MM

Set of 5 x A4 Sheets of Flexoid Gasket Paper Material

JDK01
54-Piece Jet Drill Set

54-Piece Jet Drill Set

Jet drill set comprising 50 jet drills and and 4 pin vises.

The perfect way to fine-tune any jet to suit your needs.

Also highly suited to clean clogged-up jets.

The set contains:

  • 4 pin vises to suit all drill sizes included
  • 10 drills ranging from 1,0 to 2,0 mm:
    1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0 mm
  • 20 drills ranging is size from 0.3 mm to 1.6 mm:
    0.3, 0.35, 0.4, 0.45, 0.50, 0.55, 0.6, 0.65, 0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0, 1.2, 1.3, 1.4, 1.5 & 1.6 mm
  • 20 x drills Gauge Number 80 to 61 (0.343 to 0.991 mm / 0.0135 to 0.0390 inches )

54-Piece Jet Drill Set

jet sizer
Carburettor Jet Gauges

Carburettor Jet Gauges

Calibrated gauges to measure jet sizes.

The perfect way to determine the exact size of jets, regardless of what is indicated on them.

Sometimes jets are drilled out to requirement and / or the original indicators are removed or illegible which leaves you questioning the true size.

With these gauges, you can still determine which size these jets are.

Indispensable when working on modified carburettors!

Two different sets available:

Set 1: 20 gauges, ranging from 0,45 mm to 1,50 mm
Set 2: 16 gauges, ranging from 1,50 to 3,00 mm

Priced per set!

Carburettor Jet Gauges

JSG01
Jet size gauge 0.5 to 1.5 mm

Jet size gauge 0.5 to 1.5 mm

Jet sizing tool to measure jets between 0.5 and 1.5 mm internal diameter.

Measurements are taken by inserting the tapered needle into the jet.

The size can then directly be read from the scale.

 

 

Jet size gauge 0.5 to 1.5 mm

JET REAMER
16-Piece Jet Reamer Set

16-Piece Jet Reamer Set

Jet reamer kit comprising 16 reamers and and a pin vise.

The perfect way to fine-tune any jet to suit your needs.

The set contains:

  • 1 pin vise to suit all reamer sizes in this set
  • 1 storage case
  • 16 reamers ranging is size from 0.33 mm to 2.00 mm:
    0.33; 0.40; 0.45; 0.50; 0.60; 0.70; 0.75; 0.80; 0.90; 1.00; 1.10; 1.20; 1.40; 1.60; 1.80; 2.00 mm

16-Piece Jet Reamer Set

G4074
Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit

Gunson Colortune See Through Spark Plug Kit.

The Tune-up plug for Petrol or LPG, 2 and 4 stroke engines with single, twin or multiple carburettors or fuel injection systems.

The original and best tool for seeing what's happening inside the combustion chamber of the petrol engine.

It allows you to see the combustion and to adjust the mixture by color.

Fits most petrol engines in standard form with additional adapters available for vehicles with alternative sized spark plugs.

Kit includes:

  • See-Through Spark Plug
  • Hexagonal adapter for spark plug wrench
  • Copper sealing washer
  • Extension Cord
  • Extension tube with mirror
  • Cleaning brush
  • Instructions in English

Colortune will fit most vehicles.

Extra adapter sizes available separately

Available in the following basic thread sizes:

  • 10 mm
  • 12 mm
  • 14 mm

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Article Number: G4074

Gunson Colortune See Through Spark Plug Kit

G4053
Gunson Carbalancer Carburetor Synchronizing Tool - G4053

Gunson Carbalancer Carburetor Synchronizing Tool - G4053

Gunson Car Balancer.

Internal combustion engines use a mixture of air and petrol to generate their power.

The performance therefore is influenced by the air flowing into it and the petrol that is metered out by the carburettor.

Unless the air flow in Twin or Multiple carburettors is correctly set, the correct mixture adjustment is unlikely to be achieved and this is the simplest tool to achieve that.

Suitable for use on SU, Solex, Auto-Lite (Fomoco), Stromberg, Weber and Zenith and can be adjusted to fit most carburettors including sidedraft, downdraft with air intakes (Venturi) from 25 mm to 67 mm (1”-2”) diameter

  • Easy read scale indicates the air flow and allows adjustment to optimum efficiency
  • Provides smoother and better acceleration
  • Carbalancer can be adjusted to fit most carburettors
  • Easy to follow instructions

The user manual for the Gunson Carbalancer, in English, can be downloaded HERE.

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Article Number: G4053

Gunson Carbalancer Carburetor Synchronizing Tool - G4053

MANOMETER2
2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer - Synchrometer Carbtune Pro

2 Column Manometer

The New Carbtune Pro - essential for balancing multiple carburettors.

  • Superior resolution to dial type gauges
  • Easily read scale
  • Comes complete with 2 x 5mm and 2 x 6mm ultra high temperature glass filled engineering nylon adapters and rubber hoses.
  • Adapters will suit DHLA & DCOE carburettors and many motorcycle carburettors.
  • Stainless steel columns indicate vacuum
  • No calibration or set-up required
  • High impact plastic casing and scale tubes - no glass
  • Dampers supplied to reduce fluctuations
  • Full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off adapters can be found HERE.

2 Column Manometer - Synchrometer Carbtune Pro

MANOMETER4
4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer - Synchrometer Carbtune Pro

4 Column Manometer / Synchronometer.

This is the New Carbtune Pro, the essential tool for balancing multiple carburettors.

  • The column type scales give a superior resolution compared to dial type gauges
  • Comes complete with 4 x 5 mm and 4 x 6 mm brass adapters and 4 silicone rubber hoses.
  • The supplied adapters will suit the Dellorto DHLA and Weber DCOE carburetors and many motorcycle carburettors.
  • The stainless steel columns indicate the vacuum that each cylinder draws
  • There is no calibration or set-up required
  • Made out of a high-impact plastic casing and scale tubes - not glass to prevent breakage
  • The built-in dampers reduce fluctuations
  • Supplied with full instructions

Also suitable for car- and motorcycle engines which have the possibility of hooking up vacuum lines.

Replacement line can be found HERE.
Replacement, brass, vacuum take-off adapters can be found HERE.

4 Column Manometer - Synchrometer Carbtune Pro

SYNCHRONOMETER
Synchrometer airflow meter for carburetors

Synchrometer airflow meter for carburetors

Synchrometer airflow meter for various carburetors.

Pushes into the trumpet / ram pipe / velocity stack or throat to measure the airflow to enable you to balance multiple carburettors.

  • Instructions included
  • The original genuine high quality German made product
  • Can be used for all Weber DCOE and IDF and Dellorto DHLA, DRLA carbs with round intakes or trumpets
  • Can also be used with motorcycle carburetors with round intakes

Total length of unit 121mm

Rubber cone dimensions:
Small end diameter 40mm
Large end diameter 55mm
Length of cone 36mm

Synchrometer airflow meter for carburetors

LOCTITE542-10ML
10 ml Loctite 542 Thread Sealant

10 ml Loctite 542 Thread Sealant

LOCTITE 542

Thread Sealant - medium strength.
For fine threads in hydraulic, pneumatic and general fittings.
Fast curing.

LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies.
The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration.
The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part.

Your Benefits:

  • Ideal for fine threads as used in hydraulic, pneumatic & general fittings
  • Suitable for metal threads only
  • Instant low-pressure seal
  • Resistant to fuel, oil, coolants and hydraulic fluids
  • Locks connection against vibration loosening
  • DVGW approval (EN 751-1): NG-5146AR0855

Excellently suited for sealing connections on carburetors and fuel pumps!

10 ml Loctite 542 Thread Sealant

LOCTITE243-5ML
5 ml Loctite 243 Thread Locker

5 ml Loctite 243 Thread Locker

LOCTITE 243

Threadlocking Adhesive - medium strength.

General purpose.

Suitable for all metal threaded assemblies.

LOCTITE 243 is a general purpose threadlocker of medium bond strength.
This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration.
The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces.
It is proven to be tolerant of minor contamination due to industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids.

Your Benefits 

  • Prevents loosening on vibrating assemblies, e.g. pumps, gear boxes or presses
  • Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces)
  • Proven to tolerate minor contamination by industrial oils, e.g. engine oils, corrosion prevention oils and cutting fluids
  • Permits disassembly with hand tools for servicing P1 NSF Reg. No.: 123000

5 ml Loctite 243 Thread Locker

G4125
Gunson Digital Exhaust Gas and CO Tester - G4125

Gunson Digital Exhaust Gas and CO Tester - G4125

The Gunson Digital Exhaust Gas and CO Tester is the perfect (and affordable !) tool for the DIY mechanic to measure and adjust the CO-percentage in the exhaust gases of cars, motorcycles, boats etc equipped with a petrol-driven internal combustion engines.

Allows you to measure the current CO-percentage after which you can adjust it to the required level.

This system is equipped with a pulse pump and is suitable for both leaded and unleaded petrol / gasoline.

The tester will calibrate itself in the open air, has no moving parts to reduce wear and tear and has no filters.

Measures the CO % to 0,5 % accurately throughout the range.

Power: 12 Volt car- or motorcycle battery.

The set comprises the following:

  • The Gastester with box
  • Puls pump with water trap
  • Metal exhaust probe
  • 3 Flexibel pipes
  • Operating Manual in English

If you require the owner's manual again, you can download it HERE.

Article Number: G4125

Additional instructions on adjusting the Gastester, in English, can be downloaded HERE.

This is a short instruction video, again in English:

Available from our stock, ready to be shipped.

For our complete offerings on Gunson Tools, please visit www.GunsonShop.com.

Gunson Article Number: G4125

Gunson Digital Exhaust Gas and CO Tester - G4125

KSKYSS045
Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV500SE

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV500SE

Pilot Screw Set for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XV500 SE.

Fits a multitude of Mikuni BDS and BDST carburetors.

This set consists of the following parts:

  • Pilot Screw
  • Pilot Screw Spring
  • Aluminum Washer
  • Viton O-Ring

Replaces Yamaha part number: 12R-14105-00

Required quantity per carburetor: 1

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XV500SE

KSKYSS045
Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1200

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1200

Pilot Screw Set for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha FZR 1000 Genesis.

Fits a multitude of Mikuni BDS and BDST carburetors.

This set consists of the following parts:

  • Pilot Screw
  • Pilot Screw Spring
  • Aluminum Washer
  • Viton O-Ring

Replaces Yamaha part number: 12R-14105-00

Required quantity per carburetor: 1

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1200

KSSD108
Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha V-Max 1200 VMX1200

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha V-Max 1200 VMX1200

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors as used on, amongst others, the Yamaha VMAX 1200 / VMX 1200.

Normally this diaphragm is not available as a separate spare part but as the existing stocks of complete throttle slides are getting depleted, this is an excellent alternative to such a complete slide.

Please note that replacing this diaphragm does require a certain degree of handicraft.
Please read the instructions carefully before making your purchase.
The instructions can be found HERE.

This diaphragm is supplied complete with the glue and tie-strap that are required for the assembly.

This is a Carburetor City replacement diaphragm of excellent Japanese manufacture.

Replacement Throttle Slide Diaphragm for Mikuni BDS carburetors for Yamaha V-Max 1200 VMX1200

KSKYSS045
Pilot Screw Set for Mikuni BDS carburetors for Yamaha VMX1200 V-Max

Pilot Screw Set for Mikuni BDS carburetors for Yamaha VMX1200 V-Max

Pilot Screw Set for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha VMX 1200 V-Max.

Fits a multitude of Mikuni BDS and BDST carburetors.

This set consists of the following parts:

  • Pilot Screw
  • Pilot Screw Spring
  • Aluminum Washer
  • Viton O-Ring

Replaces Yamaha part number: 12R-14105-00

Required quantity per carburetor: 1

Pilot Screw Set for Mikuni BDS carburetors for Yamaha VMX1200 V-Max

KSYT24A
Drain Plug for Mikuni BDS carburetors for Yamaha VMX 1200 V-Max

Drain Plug for Mikuni BDS carburetors for Yamaha VMX 1200 V-Max

Float Bowl Drain Plug for the Mikuni BDS carburetor on the Yamaha VMX 1200 / V-Max.

Replaces Mikuni part numbers: 12R-14191-00 (old) and 2L1-14191-00 (new)

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

Drain Plug for Mikuni BDS carburetors for Yamaha VMX 1200 V-Max

KSNTMOR021MG
Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300

Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300

Rubber (Viton) gasket for the float bowl of Mikuni BDS carburetors as used on, amongst others, the:

  • 1999 - 2001 Yamaha XVZ1300 Royal Star Deluxe S
  • 1999 - 2001 Yamaha XVZ1300 Royal Star Deluxe Venture
  • 2000 Yamaha XVZ 1300
  • 2005 - 2009 Yamaha XVZ1300 Royal Star Deluxe
  • 2006 - 2007 Yamaha XVZ1300 Royal Star Midnight Tour Deluxe

Replaces Mikuni part number: 4XV-14562-00-00

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that the gasket shown will fit your bike.

Float Bowl Gasket for Mikuni BDS carburetors for Yamaha XVZ1300

KSKYSS045
Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1300 Venture Royal

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1300 Venture Royal

Pilot Screw Set for the Mikuni BDS series carburetors as used on, amongst others, the Yamaha XVZ 1300 Venture Royal.

Fits a multitude of Mikuni BDS and BDST carburetors.

This set consists of the following parts:

  • Pilot Screw
  • Pilot Screw Spring
  • Aluminum Washer
  • Viton O-Ring

Replaces Yamaha part number: 12R-14105-00

Required quantity per carburetor: 1

Pilot Screw Set for Mikuni BDS carburetors for Yamaha XVZ1300 Venture Royal

KSYT24A
Drain Plug for Mikuni BDS carburetors for Yamaha XVZ1300 Royal Star / Venture

Drain Plug for Mikuni BDS carburetors for Yamaha XVZ1300 Royal Star / Venture

Float Bowl Drain Plug for the Mikuni BDS carburetor on the Yamaha XVZ 1300 Royal Star & Venture.

Replaces Mikuni part numbers: 12R-14191-00 (old) and 2L1-14191-00 (new)

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

Drain Plug for Mikuni BDS carburetors for Yamaha XVZ1300 Royal Star / Venture

KSYT24A
Drain Plug for Mikuni BDS carburetors for Yamaha XV500 Virago

Drain Plug for Mikuni BDS carburetors for Yamaha XV500 Virago

Float Bowl Drain Plug for the Mikuni BDS carburetor on the Yamaha XV 500 Virago.

Replaces Mikuni part numbers: 12R-14191-00 (old) and 2L1-14191-00 (new)

Although these carburetors were originally delivered on the above mentioned models of motorcycles, they are often transplanted onto other bikes and engines so the range that these gaskets might fit is much broader.

Alternatively, your bike might have been equipped with different carburettors during its life so please verify that this valve will fit your bike.

Drain Plug for Mikuni BDS carburetors for Yamaha XV500 Virago